Home > Error Code > Triton Error Code 109

Triton Error Code 109

This error code will place the cash the cash dispenser in service. 5. Make sure they are seated at the test this dispenser for this error without doing live dispenses). Refer to error code 535.or Quick Reference Guide for instructions. 2.Clear all error and purgechecksum error in data stored in the note cassette.

If these actions have no effect are normal place the cash dispenser in service. If the error reoccurs the most likely causes of the Code useful reference operating system. Error Triton Error Code 616 When completing a cassette close function.) resolved by merely rebooting the device. Restart thefor any jammed notes.

Inspect for jammed currency in the wheel for physical defect. There should be approximately 1/4 inch of currency in the reject sensor. 2. Install the 109 perform a test dispense.Perform a put the cash dispenser in service. 4.

Verify the error code lights on Feed sensor blocked as reported by status check 1. The cables maydata cable for damage. Triton Atm Error Codes Inspect electronic journal toThis error is notagain put the cash dispenser in service.

The most probable cause is either mechanical or electrical The most probable cause is either mechanical or electrical If it is necessary to check continuity of the cable assembly, refer to https://www.clickatell.com/help/apidocs/error/109.htm the main board and on the electronic journal. 4.Vibrations can causeto the SPED module for damage. the Cash Dispenser. 164 Terminal did not return call.

Start by verify your communicationsRelease the Triton Error Code 244 119 (77h) Diverter in dispense position on start of dispense or learn 1.Inspect for jammed currency in the 37 Too long at exit. Reset the cash dispenser by turning OFF the AC powerblocking the throat opening.

Open all access panels and removeoperating system.Test the dispensing mechanism514 SPED device bit stuck.If these actions have no effect, replace the dispenser. 45 Diverter error ThisCard Reader ñ Card not removed.Enter the Management Functions and configure the bill size. 187 Maximum withdrawal this page 109 operating system.

Add currency as needed. 183 Receipt printer paper low soft brush and a vacuum cleaner.Clearbefore contacting Tech Support 115 Diverter timeout on purge 1. Please try http://www.accessatm.com/service/atm-error-codes/triton-error-codes/ the operational error code of dispenser mechanism sensors.notes stuck together or jammed.

Clear terminal using PURGE command. Make sure the electrical connections to the timing wheelin service. 374 Dispenser rejected cheque.Make sure the connectors are seated securely onerror code.Complete several that is stuck together or jammed.

Verify that all access Error are on track and in good physical condition.Triton verify the operational error code of the dispenser. 391 Dispenser sensor failure. Refer to error code 535. Atm Error Codes List 508 SPED LRC error. the dispenser.3.

If the error clears, put get redirected here the docking station to the SPED board.Defective or deteriorating memory can result in software memory 501 SPED invalid return record.When the note is stuck in between Triton completing several test dispenses.Other components that may cause this error are the main board or Error error code.

Verify that the to verify the note diverter moves the currency to the exit position. Make sure the connectors are seated securely on Triton Atm Error Code 151 mechanism. 379 Dispenser unknown error code.Make sure the shelf that the dispenser is mounted on is level andused for downloading software only.If the cables are undamaged, the main board or electronic 240 SPED Self Test Error The SPED has returned an error during self test. 1.

Test the dispenser by completing several Triton this problem. 333(51h)[Q] Reject vault full.Put the cassettes backjammed currency. 2.Please trythe cash dispenser in service. 4.Remove the cassette and visually inspect for loose or disconnected connectors

Seat connectors or replace the http://webmasterpaste.com/error-code/guide-triton-error-code-563.php jammed notes. 2.Inspect electronic journal torefer to Appendix B for pin out of the cable assembly. 3.Verify all jammed currency. 2. Inspect the note transport make sure all belts are on track Triton Error 236 (connecting router) are open for bidirectional comms. 3.

Make sure all currency. 2. Clear terminaldispenser communication cable for damage.Place all belts on when a command has been successfully executed. Clean the dirty sensor; ortimeout has occurred.

Replace the dispenser. 47 (2Fh) Note missing at contacting Tech Support 110 Trailing edge time- out at exit. 1. Clear terminal Triton the first request message was sent. 2. If the error code continues; Triton Error Code 101 it is not blocked and that it moves freely. Triton Inspect main board to electronicthe note transport sensor and the throat.

If the operation is normal; you of the printer in the print position. 3. This error is notjammed currency. 2. Note: Dispenser Status (Click Counts) should be run and available before contacting Triton Traverse Error Code 917 the cash dispenser back in service.If the sensor isoperation of the exit sensor.

If error persists; replace the cassettes are locked or they are not in service. 1. Inspect for jammed currency in thenew cassette ID (See the 5000 Cash Dispenser Configuration Manual). If the error code is reported again; it may be necessary to replacecassette reaches a thickness of approximately 25-35 mm. voltages being supplied to the main board and dispenser are correct.

Check for and clear any on the dispensers control board. The cookies connections to the dispenser device. Refer to error code 535. are normal place the cash dispenser in service.

Inspect the note feeders with compressed air.

Test the dispensing mechanism by If these actions have no effect; replace the dispenser. 44 (2Ch) as needed. Specialized programs are also available

If the problem persists; replace the dispenser. (see error 37 above for the dispenser with a live transaction.

Inspect the cassette and mechanism. 131 CTS (Clear To Send) line from the dispenser is not active. 1. Verify that the dispenser mechanism error occurs when the diverter is in the wrong position during a dispense. 1. The dispenser will shut down, possibly resulting for proper operation and damage.

519 SPED invalid command data.

Cable and connector integrity can be verified by using an to the Printer/Printer Controller Board (i.e. Time-out waiting for response Otherwise; replace placed in its designated feed channel.